日本YUKEN座閥型電磁換向閥型號規格

The use of the low viscosity hydraulic fluids reduces the pressure loss
which can a rise from the passage resistance of the hydraulic fluids, leading to the system energy saving
高響應高性由于這些閥是提升型，
所以沒有重疊，可以實現高響應。
This makes it possible to use these valves in combination with 01 Series Modular Valves.
This is the leakage towards "T" port in A port block at "P" port pressure 14 MPa (2030 PSI).
 使用低粘度液壓流體減少了壓力損失，
這可以從液壓流體的通道阻力上升，導致系統節能。
These are Solenoid Operated Directional Valves of No Leak Type developed with the aim of responding the demand of the a ge including energy saving. 
Because these valves are of no leak type they allow the low viscosity hydraulic fluids to be used
否則可能會導致故障的破壞并縮短閥門的使用壽命。
 請保持NAS 1638Grade 12內的污染程度。
使用25μm或更細的線路濾波器。
Recommended Viscosity and Oil Temperatures 2  Viscosity ranging between 15 - 400 mm /s (77 - 1800 SSU). 
Oil temperatures between -15/+70°C (5 - 158°F).  Use hydraulic fluids which satisfy the recommended viscosity and oil temperatures given above.
 同時，液壓鎖消除。
不采用泄漏片式密封，內部泄漏大大降低。
ISO Comformant安裝面由于安裝面符合ISO 4401-AB-03-4-A，
因此與常規閥門可互換。
這使得可以將這些閥門與01系列模塊閥組合使用。
這是在“P”端口壓力14 MPa（2030 PSI）下A端口塊中“T”端口的泄漏。
 Control of Contamination Due caution must be paid to maintaining control over contamination of the hydraulic fluids
 which may otherwise lead to breakdowns and shorten the life of the valves.
這些是為了應對包括節能的需求而開發的無泄漏型電磁操作方向閥。
因為這些閥門是沒有泄漏的，所以它們允許低粘度液壓油

日本YUKEN座閥型電磁換向閥型號規格
No Leak Sheet type seal has been adopted and internal leak is greatly reduced.
這是在“P”端口壓力14 MPa（2030 PSI）下，A•B端口塊中的“T”端口泄漏。
High Response High Reliability Because these valves are of poppet type, there is no overlap,
 high response can be achieved.  At the same time, hydraulic lock is eliminated.                        
提示類型  電磁操作方向閥DSLG-01-3-C / O
流體類型可以使用表中列出的任何類型的液壓油。
ISO Comformant Mounting Surface Because the mounting surface conforms to ISO 4401-AB-03-4-A,
This is the leakage towards "T" port in A•B  port block at "P" port pressure 14 MPa (2030 PSI).
的粘度和油溫2粘度范圍在15 - 400 mm / s（77 - 1800 SSU）之間。
油溫在-15 / + 70°C（5 - 158°F）之間。
 使用滿足上述給出的粘度和油溫的液壓油。
污染控制必須注意保持對液壓油污染的控制，
安裝螺栓包括下表中的四個內六角頭螺釘。
以及由于壓力油內部泄漏太多而不能被傳統的閥芯型換向閥使用的回路結構。
there i s an interchangeability with the conventional valves.
 Please maintain the degree of contamination within NAS 1638Grade 12.  Use 25 µm or finer line filter.
石油基礎油合成液含水液體
使用與ISO VG 32或VG 46相當的流體。使用磷酸酯或多元醇酯液。
當使用磷酸酯流體時，需要使用特殊密封（氟橡膠），
使用前綴“F-”型號。 使用水 - 液體。
子板可用。 從上表中子板型號。
當不使用子板時，安裝表面應具有良的加工精加工。
 as well as the circuit construction which cannot be used by the conventional spool type directional valves because of too much internal leak of pressure oil.